Phase formation,structure and properties of light-weight aluminosilicate proppants based on clay-diabase and clay-granite binary mixes

One of the drawbacks of fusible clays is the narrow sintering interval due to a sharp increase in the amount of iron-silicate melt at a temperature of 1000–1100 °C, which hardens in the form of a glass phase upon cooling. This leads to a relatively low mechanical strength of the calcined samples and causes the danger of melting the granular material surface from such clays during the firing process. To increase the strength of samples of fusible clays, the influence of diabase and granitoid rocks was considered. It was found that the strengthening effect of diabase and granitoid rock additives in an amount of 20–50% in a mixture with fusible clay is due to an increase of total content of the crystalline phase (mullite, cristobalite and residual quartz) from 18–20% in clays without additives to 22–28 % - in mixtures with diabase and to 28–34% - with granitoid additives) at a temperature of 1050–1100 °C. This increase is due to the activation of synthesis processes of secondary mullite and crystallization from alkali-rich feldspar melt of amorphous silica, released from the structure of clay minerals. The established influence of the igneous rocks used made it possible to develop compositions and propose process flow sheet for producing aluminosilicate proppants based on fusible clays. The use of granitoid and diabase rocks in an amount of 20–70% with fusible clays produces lightweight aluminosilicate proppants with bulk density of 1.40–1.46 g/cm³ at temperature range of 1050–1100 °C, which can endure destructive pressures up to 34.5–52 MPa.     

变压吸附制氮(PSA)设备在炼油生产中的应用

针对某炼油装置氮气供需矛盾突出的问题,提出采用变压吸附(PSA)制氮设备,利用空压站净化风生产氮气方案,(1)降低空压站多余风量放空,减少浪费;(2)正常生产情况下,利用PSA设备生产氮气,对供氮管网压力调节。针对上述方案,结合空压站供风现状进行分析,得出结论:利用PSA制氮设备满足炼油装置高峰用氮是可行的,并提出了具体措施和运行过程中应注意的问题。     

Experimental evaluation of the luminescence performance of fired clay brick coated with SrAl2O4:Eu/Dy phosphor

This study evaluates the luminescence performance of fired clay bricks coated with SrAl₂O₄:Eu/Dy phosphor. To do so, SrAl₂O₄:Eu/Dy phosphor was first produced using the traditional solid-state reaction synthesis technique. The prepared phosphor was then used for coating fired clay bricks to analyze the luminescence performance via spectral analysis, decay characteristics, and microstructure of the bricks. The results reveal that excitation and emission spectra of the phosphor coated bricks range from 200 to 480 nm and 455 to 650 nm, respectively, suggesting that the phosphor coated bricks have the capacity of absorbing light with a wide range of wavelengths. The peak wavelength projected at 511 nm in the emission spectrum is achieved, which indicates 4f⁶5 d¹-4f⁷ transition of Europium (Eu²⁺). The repeated excitation and deexcitation of Eu²⁺ by using hole traps and trap levels offered by Dysprosium (Dy³⁺), exist between the ground and the excited state of Eu²⁺ leads to luminescent phenomenon. Moreover, the decay characteristics has revealed that phosphor coated bricks can emit light for a considerable amount of time (>8.5 min) upon the removal of the excitation source. The results reveal that phosphor coated bricks has the potential of increasing energy efficiency of residential and commercial buildings.     

Full scale investigation of GCL damage mechanisms in small earth dam retrofit applications under earthquake loading

This paper reports results of full scale testing to further explore potential GCL damage mechanisms in earth dam retrofit applications in seismically active areas; in particular, to a) investigate whether shear displacements could reduce the magnitude of GCL panel overlap during earthquake shaking; b) explore the influence of gravel particles on GCL thickness at localised point of contact; and c) observe the consequences of an accidental exposure of an uncovered GCL to short duration rainfall in terms of moisture content and effects during subsequent compaction. The results of these experiments indicate that even under severe shaking no movements were detected at the GCL panel overlap. Whereas gravel particles were observed to locally reduce the thickness of the GCL to 2.2 mm, no plowing of the particle into the GCL occurred due to a lack of shear displacement at the interface, resulting in no localised internal erosion through the barrier. Furthermore, hydration of GCL panels during construction due to surface wetting was observed to result in a state of hydration less than its post-construction state. These results indicate that although each of the three GCL damage mechanisms cannot be ruled out to ever be relevant in practice, the performance of the GCL retrofitted earth dam tested was satisfactory under even severe Level 2 earthquake shaking, and suggests that the retrofitting of small earth dams with GCLs is a promising strategy to improve their static and seismic resistance.     

Hysteresis of the water retention curves of geosynthetic clay liners in the high suction range

This paper examines two needle-punched geosynthetic clay liners' water retention behaviour at high suction ranges using the vapour equilibrium technique where super-saturated salt solutions controlled the relative humidity. This study shows that the bentonite form and its mineralogy affect the absorption/desorption of GCLs and their corresponding water retention curves. In particular, a granular bentonite-based GCL was found to absorb more and release less water than a powdered bentonite-based GCL due to its higher montmorillonite content and larger pores. The water retention curves of both GCLs exhibited very little hysteretic behaviour at high suction. Repeated wetting-drying cycles shifted the WRCs of both GCLs slightly downward with minimal impact on their degree of hysteresis.     

木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

Comparative performance of carbon nanotube and nanoclay on thermal properties and flammability behavior of amorphous polyamide/SEBS blend

Multiwall carbon nanotubes (CNT) or montmorillonite clay (MMT-30B) were added to a poly(hexamethylene isophthalamide-co-terephthalamine) (an amorphous polyamide - aPA) and styrene-ethylene/butylene-styrene graphitized with maleic anhydride (SEBS) blend, in different concentrations, in order to investigate the morphology, thermal properties and flammability behavior. Different nanoparticle localizations in the phase blend were observed through transmission electronic microscopy. CNT nanoparticles are localized in SEBS phase, and MMT-30B nanoparticles in aPA phase. No significant changes were observed on transition temperatures and thermal stability with both nanoparticle additions. However, a slight increase on storage modulus for clay nanocomposites and a slight reduction for carbon nanotube nanocomposites were observed, due to their different phase localizations. Regarding flammability, CNT nanocomposites showed better performance as a flame retardant when compared to samples with MMT-30B. Although the MMT-30B nanocomposites could not be classified according to the UL-94 criteria, no dripped flaming particles were observed, due to the a char barrier formation on the polymer surface. The CNT nanocomposites were classified according to the UL-94 criteria as V-2. The CNT's selective localization on the SEBS phase decreases its heat-release rate, but no interconnected network structure was formed in the matrix to suppress the dripping flaming particles.